Samsung dryer not heating (HE or HC code): what to check and which part to replace
When a Samsung electric dryer runs but stays cold, the heating element is the usual failed part, and a blown thermal fuse or a clogged vent is the next thing to check. Samsung gas dryers use a burner with an igniter instead, so start with the gas supply there.
Samsung lists HE, HC and HE1 as heating errors. HE usually appears when the dryer is not heating properly; HC often follows overheating, most commonly from a blocked vent. Clean the vent first, then work through the checks below.
Check these first
- Check the breaker. Electric dryers use a double breaker; if one half trips, the drum turns but there is no heat.
- Check the vent. A clogged vent can trigger a heating or vent-blockage error and blow the thermal fuse. Clean the lint screen and the full duct.
- Test the thermal fuse on the heater housing at the back. With the dryer unplugged, a good fuse shows continuity.
- Test the element. With the wires off, a good element reads roughly 10 ohms; an open reading means it is broken.
Samsung dryer heating elements
DC47-00019A is the coil alone; DC97-14486A comes with the housing.
Most bought first, by share of estimated Amazon sales across 3 part numbers. All dryer heating element part numbers
The heating element coil for many Samsung electric dryers (more than 120 listed models, including DV42H, DV45H and DVE50R models). By far the most bought.
24 listings from 21 brands, including Samsung's own part. Most-bought aftermarket: Pulluty, AMI PARTS, TOMOON. Fits 126 listed models, for example DV206LEW/XAC, DV209AEW/XAA, DV210AES/XAC, DV210AEW/XAA.
Compare DC47-00019A replacementsThe element assembly with its housing, for more than 120 listed Samsung dryers. Choose it when the housing is damaged as well as the coil.
14 listings from 14 brands, including Samsung's own part. Most-bought aftermarket: Aremae, Funmit, AMI PARTS. Fits 128 listed models, for example DV206LEW/XAC, DV209AEW/XAA, DV210AES/XAC, DV210AEW/XAA.
Compare DC97-14486A replacementsA 3-wire duct heater element for some Samsung dryers, such as the DV42H5600 and DV45K6500 models.
7 listings from 7 brands, including Samsung's own part. Most-bought aftermarket: Casmer, Vypart, ApplianPar. Fits 78 listed models, for example DV42H5600EF/AC, DV42H5600EG/A3, DV42H5600EP/A3, DV42H5600EP/AC.
Compare DC93-00154A replacements
More on Samsung elements
See the full Samsung dryer heating element guide for the part numbers and models.
Safety
- Unplug the dryer before opening it; on gas models, also turn off the gas.
- Never bypass the thermal fuse.
Frequently asked questions
What do the HE and HC codes mean on a Samsung dryer?
Both are heating errors. HE usually means the dryer is not heating properly (a failed element, thermal fuse or sensor); HC often means it ran too hot, most often because the vent is blocked. Clean the vent and lint screen first.
Why is my Samsung dryer not heating?
Usually a broken heating element, a blown thermal fuse (often after a clogged vent) or a tripped half of the breaker on electric models.
What is the most common Samsung dryer heating element?
DC47-00019A, at about 74% of estimated Amazon sales across the Samsung element numbers we track.
Where is the thermal fuse on a Samsung dryer?
On most Samsung electric dryers it is on the heater duct at the back, behind the rear panel. Unplug the dryer before removing the panel.
As an Amazon Associate I earn from qualifying purchases. Sales shares are our estimates of Amazon sales and are rounded. Aftermarket parts are made by third parties, not by the makers. How this works