Samsung dryer heating element: find your part number
If your Samsung dryer runs but stays cold, or takes far too long to dry, the heating element is a common cause. Most Samsung electric dryers use one of 3 element part numbers. This guide shows which one your dryer takes and what other shoppers buy.
Samsung's own listings take 2% of estimated Amazon sales across these numbers; the rest goes to 33 aftermarket brands.
Samsung dryer heating element part numbers, most bought first
Share of estimated Amazon sales across all 3 numbers. Open a part to compare every replacement and search its full model list.
The heating element coil for many Samsung electric dryers (more than 120 listed models, including DV42H, DV45H and DVE50R models). By far the most bought.
24 listings from 21 brands, including Samsung's own part. Most-bought aftermarket: Pulluty, AMI PARTS, TOMOON. Fits 126 listed models, for example DV206LEW/XAC, DV209AEW/XAA, DV210AES/XAC, DV210AEW/XAA.
Compare DC47-00019A replacementsThe element assembly with its housing, for more than 120 listed Samsung dryers. Choose it when the housing is damaged as well as the coil.
14 listings from 14 brands, including Samsung's own part. Most-bought aftermarket: Aremae, Funmit, AMI PARTS. Fits 128 listed models, for example DV206LEW/XAC, DV209AEW/XAA, DV210AES/XAC, DV210AEW/XAA.
Compare DC97-14486A replacementsA 3-wire duct heater element for some Samsung dryers, such as the DV42H5600 and DV45K6500 models.
7 listings from 7 brands, including Samsung's own part. Most-bought aftermarket: Casmer, Vypart, ApplianPar. Fits 78 listed models, for example DV42H5600EF/AC, DV42H5600EG/A3, DV42H5600EP/A3, DV42H5600EP/AC.
Compare DC93-00154A replacements
Electric or gas? Check this first
Only electric dryers have a heating element. A Samsung gas dryer heats with a burner and an igniter, so none of these parts apply to it.
How to find the right part number
- Read the model number. On most Samsung dryers the label is inside the door opening or on the back. Write down the full number, including the part after the slash.
- Match it to a part number. Each part page lists the dryer models the element fits.
- Coil or assembly? DC47-00019A is the coil alone; DC97-14486A comes with the housing. If the housing is fine, the coil is the cheaper fix.
Make sure it is really the element
Unplug the dryer before you open it: it runs on 240 volts.
- Test the element. With the wires off, a multimeter across the terminals should read roughly 10 ohms. An open reading means the coil is broken.
- Check the thermal fuse and thermostats. Samsung dryers have a thermal fuse and high-limit thermostat on the heater housing. If one has failed, the element gets no power.
- Clean the vent. A clogged vent makes the dryer overheat, which blows the fuse and shortens element life.
How to replace the element
- Unplug the dryer, pull it out and disconnect the vent.
- Remove the rear panel. On most Samsung electric dryers the heater duct is at the lower back, behind this panel.
- Photograph and disconnect the wires, including the thermal fuse and thermostat on the duct.
- Remove the duct screws and lift the heater out. DC47-00019A is the coil alone, fitted into the old duct; DC97-14486A is the full assembly with the duct.
- Test the thermal fuse on the duct and replace it if it shows no continuity; a blown fuse often goes with a failed element.
- Refit, reconnect as photographed, clean the vent and run a timed dry cycle to check for heat.
Samsung's own element or an aftermarket one?
Across these 3 part numbers, Samsung's own listings make up 2% of estimated Amazon sales (May to June 2026). The rest goes to 33 aftermarket brands, led by Pulluty, AMI PARTS and Funmit.
Aftermarket elements are usually much cheaper. Many listings call their element "upgraded"; that is the seller's claim, so compare the coil and terminals with your old part, and check that the listing names your dryer model.
Frequently asked questions
How do I replace a Samsung dryer heating element?
Unplug the dryer, remove the rear panel, photograph and disconnect the wires on the heater duct, unscrew the duct and lift the heater out. Fit the new coil or assembly, test the thermal fuse, and clean the vent before testing.
What is the most common Samsung dryer heating element?
By estimated Amazon sales, DC47-00019A is the most bought, at about 74% of sales across the 3 Samsung element numbers we track.
What is the difference between DC47-00019A and DC97-14486A?
DC47-00019A is the heating coil alone. DC97-14486A is the element with its housing, for when the housing is damaged too.
Why is my Samsung dryer not heating?
The heating element is the most common cause, but a blown thermal fuse, a failed high-limit thermostat or a clogged vent can also stop the heat. Test the element and fuse with a multimeter, and clean the vent.
As an Amazon Associate I earn from qualifying purchases. Sales shares are our estimates of Amazon sales and are rounded. Aftermarket parts are made by third parties, not by Samsung. How this works
All dryer heating element part numbers · All Samsung parts · All guides