Whirlpool dryer heating element: find your part number
If your Whirlpool dryer tumbles but stays cold, or a normal load now takes two cycles, the heating element is the most common cause. Whirlpool has used 6 different element part numbers across its electric dryers, and they are not interchangeable. This guide shows how to find the one your dryer takes and what other shoppers buy.
The same parts are used in dryers sold under Maytag, Amana, Roper, Crosley, KitchenAid and many Kenmore brands, because Whirlpool built them. A Kenmore model number that starts with 110 is a Whirlpool-built dryer.
Whirlpool dryer heating element part numbers, most bought first
Share of estimated Amazon sales across all 6 numbers. Open a part to compare every replacement and search its full model list.
A coil element that mounts in the heater box behind the drum. It fits most full-size Whirlpool-built electric dryers with a rear heater, including many Whirlpool, Kenmore 70 and 80 series, Roper and Amana models. Sellers often list it with the older number 3403585 and with W10724237.
23 listings from 21 brands, including Whirlpool's own part. Most-bought aftermarket: MONKEMON, AMI PARTS, LFORBB. Fits 36 listed models, for example EED4400WQ0, LEC6858AQ3, LEG8858JZ0, LER5636EZ01.
Compare 279838 replacementsAn element mounted on its own plate, used in many Whirlpool Cabrio and Duet, Kenmore HE and Elite, and Maytag Bravos electric dryers. Also sold as 3387747.
18 listings from 17 brands, including Whirlpool's own part. Most-bought aftermarket: TOMOON, APPLIANCEMATES, Pulluty. Fits 132 listed models, for example GEC9858EQ0, GEC9858EQ1, GEC9858EZ0, GEC9858EZ1.
Compare WP3387747 replacementsThe element with its housing for Whirlpool Duet front-load electric dryers such as the WED9750 and WED92HE models. Also sold as 8544771.
9 listings from 9 brands, including Whirlpool's own part. Most-bought aftermarket: AMI PARTS, Beaquicy, BlueStars. Fits 7 listed models, for example WED7590FW0, WED85HEFC0, WED85HEFW0, WED92HEFC0.
Compare WP8544771 replacementsAn element for some older Whirlpool and Kenmore dryers, including LE-series models. Also sold as 4391960.
2 listings from 2 brands, including Whirlpool's own part. Most-bought aftermarket: AMI PARTS. Fits 12 listed models, for example LE3000XSWO, LE5700XSNW, LE5800XSN3, LE7680XSW2.
Compare WP4391960 replacementsA Maytag-original element (the Y prefix marks Maytag's own numbering) for older Maytag electric dryers.
2 listings from 2 brands, including Whirlpool's own part. Most-bought aftermarket: ForeverPRO.
Compare WPY313538 replacementsAnother Maytag-original element for older Maytag, Amana and Speed Queen-style dryers.
2 listings from 2 brands, including Whirlpool's own part. Most-bought aftermarket: Edgewater Parts.
Compare WPY503978 replacements
Electric or gas? Check this first
Only electric dryers have a heating element. A gas dryer heats with a burner and an igniter, so if yours has a gas line, none of these parts apply. Electric dryers plug into a large 240-volt outlet; gas dryers use a normal 120-volt plug plus a gas pipe.
How to find the right part number
- Read the model number. On most Whirlpool-built dryers the model and serial tag is inside the door opening, on the frame or the edge of the door. Write the full model number down, including the letters and digits at the end.
- Match it to a part number. Each part page on this site lists the dryer models the part fits. The examples in the table above are a starting point; open the part page to search the full list.
- Or read the old element. The number is sometimes stamped on the element's bracket or printed on a label on the heater housing. It is easiest to read once the element is out.
Make sure it is really the element
A burnt-out element is common, but three other faults cause the same no-heat symptom, and two of them are cheaper to fix. Unplug the dryer before you open it: it runs on 240 volts.
- Test the element. With the wires off, a multimeter across the two terminals should read roughly 10 to 12 ohms on most of these elements. An open reading means the coil is broken and the element needs replacing.
- Check the thermal fuse and thermal cut-off. These are small safety parts on the heater housing or blower. If one has blown, the element gets no power even though it is fine.
- Clean the vent. A clogged exhaust vent makes the dryer overheat, which blows the fuse and shortens element life. If you replace the element without clearing the vent, the new one can fail the same way.
How to replace the element
- Unplug the dryer and pull it away from the wall. Disconnect the vent.
- Open the right panel. On most Whirlpool-built 29-inch dryers (Whirlpool, Maytag, Kenmore, Roper), the element housing is behind the rear panel; on many front-load pairs (Duet and similar), it is reached by removing the top and front panel.
- Photograph the wires, then pull them off the element terminals.
- Remove the screw holding the housing and slide it out. Some parts (such as 279838) are the coil only and are threaded into the old housing; others come with a new housing.
- Check the thermal fuse and high-limit thermostat while it is open; they often fail with the element. Replace any that show no continuity.
- Refit, reconnect the wires as photographed, clean the vent and test a timed dry cycle.
Whirlpool's own element or an aftermarket one?
Across these 6 part numbers, Whirlpool's own listings make up under 1% of estimated Amazon sales (May to July 2026). The rest goes to 31 aftermarket brands, led by MONKEMON, AMI PARTS and APPLIANCEMATES.
Aftermarket elements are made by other companies to the same fit and are usually much cheaper. Build quality varies by brand. Many listings call their element "upgraded"; that is a seller's claim, so compare the wattage, the coil and the terminal layout with your old part, and check that the listing names your dryer model.
Frequently asked questions
How do I replace a Whirlpool dryer heating element?
Unplug the dryer, remove the rear panel (or the front panel on many front-load models), photograph and disconnect the wires, remove the housing screw and slide the element out. Fit the new one, check the thermal fuse and high-limit thermostat, and clean the vent before testing.
What is the most common Whirlpool dryer heating element?
By estimated Amazon sales, 279838 is the most bought, at about 69% of sales across Whirlpool's 6 element numbers. It fits most full-size Whirlpool-built electric dryers with a rear heater box. Check your model number before you buy.
Do Maytag, Kenmore and Amana dryers use the same heating element?
Many do, because Whirlpool built them. Kenmore models starting with 110, and most Maytag, Amana, Roper and Crosley electric dryers made since the 2000s, use Whirlpool part numbers. Older Maytag dryers may take a Maytag-original Y-prefix element instead.
Does a gas Whirlpool dryer have a heating element?
No. Gas dryers heat with a burner and an igniter. A heating element is only used in electric dryers.
How do I know if my dryer heating element is bad?
Unplug the dryer, disconnect the element's wires and measure across its terminals with a multimeter. Most read roughly 10 to 12 ohms when good; an open reading means the coil is broken. If the element tests fine, check the thermal fuse, thermal cut-off and the vent.
As an Amazon Associate I earn from qualifying purchases. Sales shares are our estimates of Amazon sales and are rounded. Aftermarket parts are made by third parties, not by Whirlpool. How this works
All dryer heating element part numbers · All Whirlpool parts · All guides